Dishwasher Repairacross South Florida.

Drain pump impeller is obstructed by broken glass, label adhesive, or food debris; the drain hose loop is kinked; or — very common — the garbage disposal knock-out plug was never removed during a disposal install. The dishwasher will never drain until that plug is out. We check all three on a $59 diagnostic.

E15 means the AquaStop float in the base pan has detected water where it should never be — Bosch's built-in leak protection doing its job. Tilting the machine to reset the float treats the symptom, not the leak. Our technician pulls the unit, traces the water with a dye test through the supply connections, inlet valve, and pump seal, and repairs the true source. Nearly every E15 on a Bosch 300, 500, 800, or Benchmark series is resolved in a single visit.

Three usual suspects in South Florida kitchens: hard-water scale blocking the spray-arm jets, a worn chopper or macerator blade letting food circulate back onto the load, or a heater that never brings the wash water up to proper sanitizing temperature. We verify each of them during the diagnostic, descale where needed, and keep chopper kits on the truck for Whirlpool and KitchenAid Tall Tub platforms.

Yes. Miele G5000, G6000, G7000, and the older Optima G2000 lines are part of our regular service mix. Miele uses heat-pump drying systems and brushless DC circulation pumps that are different from mainstream brands. Senior technicians handle Miele calls and we carry the most common Miele parts on the senior truck.

Door latch microswitch has failed (the unit does not think the door is closed), the ribbon cable from the user-interface board to the main control board has corroded, or a thermal fuse on the control board has blown. Latch assemblies are stock items for high-volume brands. Control board thermal fuse is re-solderable on some Whirlpool boards.

Heating element replacement on Whirlpool, KitchenAid, GE, and Maytag dishwashers runs $190 to $280 all-in for the part and labor — the $59 diagnostic is free once you approve the repair. Bosch and Miele use heat-pump drying with no traditional element — those repairs are different and we quote separately. The signature symptom is dishes still warm but the cycle never finishes.

Door gasket has a flat spot or tear (common after 6 to 10 years), or the inlet valve is dribbling past its shutoff and overfilling the tub so water spills over the door seal during the wash phase. We dye-test the gasket and inlet valve to isolate. Gasket swaps are quick; inlet valves are model-specific and stock for Whirlpool, KitchenAid, GE, and Bosch.

On mainstream brands depends on the failure. Cheap fixes like door latches, gaskets, inlet valves, and choppers are almost always worth doing. A failed circulation pump or main control board on a 10-plus year old commodity dishwasher often is not. On Bosch and Miele — almost always worth repairing because the heat-pump drying systems and stainless tubs are designed for 15-plus years.

Yes — we manage the entire changeover: water supply, drain routing, electrical connection, precise leveling, and balancing the door springs, then remove the old unit before we leave. A standard installation is $185 to $260, with the range driven by the state of the under-sink plumbing (new shutoffs, or a fresh tailpiece on the disposal). Integrated panel-ready models from Miele and Bosch Benchmark are a longer, more careful job — those we quote individually.

A flat $59 covers the visit and a full factory-level diagnosis — and it is credited back in full the moment you approve the repair. You pay it only if you choose not to proceed. There is no premium surcharge for Sub-Zero, Wolf, Miele, or Thermador work; the diagnosis is the same disciplined process on every unit.

We hold priority dispatch windows for luxury kitchens across Miami-Dade, Broward, and Palm Beach. Call early and we can usually schedule a white-glove visit the same day; for built-in and integrated units we match you with the senior technician trained on your platform rather than simply sending the next available van.

Yes. Berne Appliance Repair is fully licensed and insured in the state of Florida, and we carry the general liability coverage that gated communities, condo associations, and high-rise buildings require. We provide a certificate of insurance to your management company on request, before the visit.

Our work centers on the high-end and built-in market — Sub-Zero, Wolf, Miele, Thermador, Viking, Gaggenau, La Cornue, JennAir Luxury, Bosch Benchmark, GE Monogram, Liebherr, and EuroCave. Our technicians are factory-trained on these platforms, and we also service everyday brands such as LG, Samsung, and KitchenAid when they share a luxury kitchen.

Tiered parts coverage plus a 90-day labor warranty. Sealed-system welds carry our longest protection — a full decade. Mechanical components are protected for two years, electronics and electrical for one. Labor is backed for 90 days — if the same fault returns, we come back at no charge. On premium platforms we source OEM parts through the factory channel, and the part number goes on your invoice so the repair is fully documented.