Miele dishwasher repairacross South Florida.
G5000, G6000 and G7000 series, panel-ready and freestanding, AutoDos and PowerDisk. F11 drain faults, F14 and F24 circulation and water intake, F32 door, F70 water-in-base, scale from Miami water, salt reservoir and rinse-aid errors. $59 diagnostic, free with the repair, same-day dispatch across Miami-Dade, Broward and Palm Beach.
- 19Full-time techniciansNot subcontractors
- 4.79From 1254 verified reviewsGoogle, Yelp & other platforms
- $59Diagnostic visitCredited to your repair
- 70Cities coveredMiami-Dade · Broward · Palm Beach
- PriorityMost visits booked <1 hourOpen 7 days · 7 AM – 9 PM
- 10-yrParts warranty up to 10 years90-day labor · Licensed & insured
G5000 to G7000: one hydraulic layout, three generations of control
Every Miele dishwasher built since the G5000 series shares the same bones: a stainless tub, a circulation pump with its own heater, a separate drain pump in the sump, an inlet with a water-protection valve on the hose, and a float in the base pan that shuts the whole thing down the moment it sees water. What changed across G5000, G6000 and G7000 is the control: the G7000 added AutoDos with the PowerDisk cartridge, Wi-Fi through Miele@home, and a fault memory the technician can read. The failure pattern did not change. The drain pump, the circulation pump and the door hardware are where a Miele dishwasher spends its service life, and they fail in a known order.
Miami water is the second half of the story. Miele dishwashers are built for softened water and carry their own water softener, which needs regenerating salt in the reservoir under the lower basket. Owners who never fill it, or fill it with dishwasher detergent by mistake, get white film on glassware and then a scaled circulation heater that trips F70-style faults years early. A dishwasher that shows the salt indicator constantly, or that has cloudy glasses after every cycle, is asking for the softener to be serviced before it is asking for a pump.
The fault codes are honest once you know the vocabulary. F11 is the drain pump not clearing the sump in time; F14 and F24 are the circulation pump or its pressure sensor; F32 and F36 are the door lock and door switch; F70 is water in the base pan and the float has tripped; F52 and F53 are the circulation pump speed sensor. Each code narrows the diagnosis to one or two parts, which is why dispatch asks for it before the truck rolls.
Code-first diagnosis, OEM pumps, softener serviced on every visit
A Miele visit starts with the fault memory, then the sump. We pull the drain pump and check the impeller and the non-return valve before condemning it, because a shard of glass in the sump produces F11 for the price of ten minutes. Circulation pumps are tested for winding resistance and for the scale that Miami water leaves on the heater element. Door springs and the lock are checked on every visit past year five, since a sagging panel-ready door strains the lock and produces F32 without the lock being at fault.
We carry the drain pumps, door locks, inlet valves and float switches that fail most, and we order circulation pumps and control modules through Miele's distribution in two to four business days. The water softener is checked and reset on every visit, and if the reservoir has been filled with the wrong product we flush it. The $59 diagnostic is free when you approve the repair, every part carries the 90-day parts and labor warranty, and the repair is logged against the serial so the next visit starts with the history.
Miele dishwasher repair — failures we see.
Documented from the platform, not a brochure.
The most common Miele dishwasher fault in South Florida. A blocked non-return valve or a glass shard in the drain pump impeller three times out of four; the pump motor itself the fourth time. We clear and test before replacing, and we check the drain hose loop, because a hose pushed too far into the disposal siphons and reproduces the code.
The wash arms turn weakly or not at all, dishes come out dirty, and the code lands mid-cycle. A scaled or failed circulation pump, or the pressure sensor that tells the control the sump is full. We meter the pump windings and check the heater for scale before ordering, since a scaled heater on a G6000 fails the same way for a fraction of the cost.
Any leak inside the cabinet, from a split hose, a cracked pump housing or a door seal, drops water on the float and the machine stops and pumps continuously. We find the source with the panel off, fix it, and dry the base so the float resets. On panel-ready units a door that closes out of alignment is a common cause.
The door lock or the door switch, often strained by a sagging custom panel on a spring set that was never adjusted for the panel weight. We replace the lock and reset the spring tension in the same visit, because replacing the lock alone under a heavy panel brings the code back.
The built-in water softener has run out of regenerating salt, was filled with detergent, or its solenoid has failed. Scale then builds on the heater and the tub. We flush and reset the softener, replace the solenoid if it has failed, and descale the circulation path before the next fault appears.
The G7000 AutoDos dispenser has its own motor and sensor. A disk that reads empty when it is not, or a dispenser that never turns, is the AutoDos unit or its harness. We test it separately from the wash system.
Rinse aid empty or the rinse-aid dispenser stuck, or the AutoOpen door drying not triggering on G6000 and G7000 units. The dispenser is a same-visit part; the AutoOpen actuator comes through distribution.
Debris in the drain pump, or a circulation pump bearing on its way out. Caught at the noise stage it is a pump; run to failure it can take the heater with it. A new noise is worth a call before it becomes a bigger one.
Typical Miele dishwasher repair costs.
| Repair | Typical range | Notes |
|---|---|---|
| Diagnostic visit | $59 | Free with repair |
| Sump and non-return valve clearing (F11) | $140–$220 | The most common fix; glass and debris |
| Drain pump | $220–$380 | Truck stock for G5000 to G7000 |
| Door lock or door switch (F32, F36) | $220–$380 | Spring tension reset included |
| Water inlet valve or water-protection hose | $200–$360 | |
| Leak trace and float reset (F70) | $160–$280 plus the failed part | |
| Softener solenoid and flush | $200–$340 | Descaling of the circulation path included |
| Rinse-aid dispenser or AutoOpen actuator | $180–$340 | |
| AutoDos dispenser unit (G7000) | $280–$460 | |
| Circulation pump with heater (F14, F24) | $420–$720 | Ordered through Miele distribution, 2-4 business days |
| Control module | $380–$680 | Only after the fault memory and meter confirm it |
Typical parts-plus-labor ranges for South Florida jobs on G5000, G6000 and G7000 series dishwashers; panel-ready units with heavy custom panels add spring and alignment work. Written quote after the $59 diagnostic, free if you approve the repair. 90-day parts and labor warranty.
Specialists for Miele at Berne.
The technicians on the Berne roster who carry Miele factory training, model-specific parts on the truck, and the diagnostic habit Miele platforms reward.
Miele dishwasher repair — questions we get
My Miele dishwasher shows F11 and has water in the bottom. Is the pump dead?
Usually not. F11 means the drain pump did not clear the sump in time, and three times out of four the cause is a glass shard in the impeller or a blocked non-return valve, which is $140 to $220 to clear. When the pump motor itself has failed, replacement runs $220 to $380 and closes the same visit.
Why are my glasses cloudy after every Miele cycle?
The built-in water softener is out of regenerating salt, was filled with the wrong product, or its solenoid has failed. Miami water scales the heater fast without it. We flush and reset the softener, replace the solenoid if needed, and descale the circulation path, $200 to $340.
What does F70 mean on a Miele dishwasher?
Water in the base pan has tripped the float and the machine is pumping continuously to protect the floor. Something inside is leaking: a hose, a pump housing or the door seal. We trace it, fix the part, and dry the base so the float resets. $160 to $280 for the trace plus the part.
Is a 12-year-old Miele dishwasher worth repairing?
Almost always. Miele builds the tub and the hydraulics to run twenty years, and the parts that fail, pumps, locks, valves and dispensers, cost $140 to $460. Even a circulation pump at $420 to $720 is a fraction of a new G7000. The one case we quote a replacement is a control module and a circulation pump failing in the same year on a G5000.
Are you an authorized Miele service center?
No. Berne is an independent service company, not affiliated with Miele. For a dishwasher still under factory warranty, Miele's own service protects the coverage and is the right call. Out of warranty, an independent shop that has opened hundreds of Miele dishwashers gets to you faster and charges less, and we will say so if your case belongs on the other side of that line.
Request a callback — or just call us.
Open 7 days. Priority scheduling — most visits booked within the hour.
- Phone(754) 345-4515
- HoursOpen 7 days · 7 AM – 9 PM
- Service areaMiami-Dade · Broward · Palm Beach
High-end appliance down? $59 brings a factory-trained specialist to your door.
Call, book online, or text us — priority scheduling for Sub-Zero, Wolf, Miele, Thermador and Viking.