Refrigerator Repair inWest Palm Beach, FL.

Probably not. Older West Palm electrical systems pass surges that take out the control board or compressor start relay — both repairable — while the compressor itself usually survives. We test the start circuit and the board at the diagnostic before any replacement conversation. It is the most common post-storm finding in the historic districts.

Daily. The newer towers run the same builder-grade models across hundreds of units, so their failure patterns — ice maker assemblies, evaporator fans, board relays — are thoroughly familiar, and the common parts ride on our Palm Beach County trucks. We handle COI and service-elevator requirements with your building before the visit.

We hold priority windows for West Palm Beach and confirm an arrival time by phone so nobody waits open-ended. A factory-trained specialist comes to your West Palm Beach home, and we cover Downtown WPB, Northwood, El Cid and the surrounding neighborhoods.

A flat $59 diagnostic brings a factory-trained specialist to your West Palm Beach home for a full assessment, and that fee is credited toward the repair when you approve the work. Most refrigerator repairs in West Palm Beach fall between $150 and $600 depending on the part — quoted in writing before anything starts.

Almost certainly. Our West Palm Beach specialists are factory-trained on Sub-Zero, Viking, Thermador, LG and the rest of the premium platforms — senior techs handle built-in and panel-ready units, with common parts on the truck so most repairs finish on the first visit.

Most often this is a failed evaporator fan, blocked airflow, or a defrost system issue. Our technician will diagnose on-site and quote the repair before any work starts.

Almost always worth repairing. Sub-Zero units are designed for 20+ years of service — replacing one costs $10K–$20K, while most repairs fall in the $200–$800 range. We'll give you an honest assessment.

Yes — including Sub-Zero built-ins, integrated columns, Thermador Freedom, Miele MasterCool, and Viking Professional.

On a high-end unit they are the same thing — a flat $59 diagnostic. It covers the visit, a full factory-level diagnosis, and a written quote on the repair. Approve the work and the fee is credited back in full. Decline and the $59 is all you owe — there is no premium surcharge for built-in or integrated platforms.

On 600 and 700-series Sub-Zero built-ins the ice maker pivot bushings dry out and bind, the optic emitter and receiver get dusty, or the water inlet valve solenoid sticks. We carry the Sub-Zero pivot kit on the truck for the common pre-2017 models. Newer 7000-series units use a different harvest module that we order as needed.

Most repairs finish on the first visit in 45 to 90 minutes once the diagnostic is done. Sealed-system work (compressors, condensers, evaporators) is a longer call — typically 2 to 4 hours and requires EPA-certified refrigerant handling. Built-in Sub-Zero and Thermador work sometimes runs to a second visit because the part has to come from the factory channel.

The defrost drain at the back of the freezer floor has frozen over with ice and food residue. Water from the normal defrost cycle has nowhere to go, overflows the drain pan, and runs forward. A 30-minute fix in most cases — we clear the drain with hot water and install a copper drain clip so it does not recur.

Yes. Viking VCBB, VCFF, and VRI-series built-ins are part of our regular service mix and we carry the common Viking parts — evaporator fan motors, defrost heaters, ice maker assemblies, and door gaskets. Senior technicians handle Viking calls because the platform has its own service quirks separate from Sub-Zero.

Almost always the condenser fan motor with dry bearings, or a piece of debris (cardboard, paper, on patio units sometimes a gecko) hitting the fan blade. On built-in Sub-Zero 600 and 700-series the condenser fan sits up top and is easy to overlook. We pull the back grille, inspect, lubricate or replace, and clear the condenser coil on the same visit.

Usually a failing thermistor giving the control board a wildly fluctuating temperature reading — the board reacts by short-cycling the compressor. Less common is a low refrigerant charge causing the compressor to short-cycle on the overload protector. Thermistor swaps are 20-minute jobs; sealed-system work is an EPA-certified call and quoted separately.

Compressor replacement on a Sub-Zero built-in runs $1,400 to $2,400 all-in including the part, EPA refrigerant work, and labor. On older 500-series and 600-series units with R-134a the part cost is reasonable; newer 7000-series with R-600a refrigerant adds a premium. We always quote in writing before opening the sealed system.

A flat $59 covers the visit and a full factory-level diagnosis — and it is credited back in full the moment you approve the repair. You pay it only if you choose not to proceed. There is no premium surcharge for Sub-Zero, Wolf, Miele, or Thermador work; the diagnosis is the same disciplined process on every unit.

We hold priority dispatch windows for luxury kitchens across Miami-Dade, Broward, and Palm Beach. Call early and we can usually schedule a white-glove visit the same day; for built-in and integrated units we match you with the senior technician trained on your platform rather than simply sending the next available van.

Yes. Berne Appliance Repair is fully licensed and insured in the state of Florida, and we carry the general liability coverage that gated communities, condo associations, and high-rise buildings require. We provide a certificate of insurance to your management company on request, before the visit.

Our work centers on the high-end and built-in market — Sub-Zero, Wolf, Miele, Thermador, Viking, Gaggenau, La Cornue, JennAir Luxury, Bosch Benchmark, GE Monogram, Liebherr, and EuroCave. Our technicians are factory-trained on these platforms, and we also service everyday brands such as LG, Samsung, and KitchenAid when they share a luxury kitchen.